Guided-Wave Radar for Level Measurement
- Application:Solid material, Strong dust, easy to crystallize, condensation occasion
- Precision:±15mm
- Process Pressure:-0.1 ~ 0.1MPa
- Shell:Aluminum
- Measuring Range:70M
Datum measurement: Screw thread bottom or the sealing surface of the flange.
Note: Make sure the radar level meter the highest level cannot enter the measuring blind area (Figure D shown below).
Features
♦ Small antenna size, easy to install; Non-contact radar, no wear, no pollution.
♦ Almost no corrosion, bubble effect; almost not affected by water vapor in the atmosphere, the temperature and pressure changes.
♦ Serious dust environment on the high level meter work has little effect.
♦ A shorter wavelength, the reflection of solid surface inclination is better.
♦ Beam angle is small, the energy is concentrated, can enhance the ability of echo and to avoid interference.
♦ The measuring range is smaller, for a measurement will yield good results.
♦ High signal-to-noise ratio, the level fluctuation state can obtain better performance.
♦ High frequency, measurement of solid and low dielectric constant of the best choice.
Suitable for Medium |
Solid material,Strong dust |
Explosion-proof Grade |
Exia IIC T6 Ga |
Measuring Range |
70 meters |
Frequency |
26 GHz |
Temperature: |
-40℃ ~ 250℃ |
Measurement Precision |
±15mm |
Process Pressure |
-0.1 ~ 0.1MPa |
The signal Output |
(4 ~ 20) mA/HART (Two |
The Scene Display |
Four digital LCD |
Shell |
Aluminum |
Connection |
Universal Flange |
Protection Grade |
IP67 |
License | ||||||||
P | Standard (Non-explosion-proof) | |||||||
I | Intrinsically safe (Exia IIC T6 Ga) | |||||||
G | Intrinsically safe type, Flameproof (Exd (ia) IIC T6 Ga) | |||||||
Process Connection / Material | ||||||||
G | Thread G1½″A / Stainless Steel 304 | |||||||
N | Thread 1½″ NPT / Stainless Steel 304 | |||||||
B | Flange DN80 / Stainless Steel 304 | |||||||
C | Flange DN100 / Stainless Steel 304 | |||||||
D | Flange DN125 / Stainless Steel 304 | |||||||
E | Flange DN150 / Stainless Steel 304 | |||||||
F | Flange DN200 / Stainless Steel 304 | |||||||
H | Flange DN250 / Stainless Steel 304 | |||||||
M | Flange DN80 / Cardan joint ( Nickel plated carbon steel ) | |||||||
K | Flange DN100 / Cardan joint ( Nickel plated carbon steel ) | |||||||
T | Flange DN125 / Cardan joint ( Nickel plated carbon steel ) | |||||||
Z | Flange DN150 / Cardan joint ( Nickel plated carbon steel ) | |||||||
W | Flange DN200 / Cardan joint ( Nickel plated carbon steel ) | |||||||
V | Flange DN250 / Cardan joint ( Nickel plated carbon steel ) | |||||||
Y | Special Custom-tailor | |||||||
Antenna Type / Material | ||||||||
B | Horn Antenna Φ46mm / Stainless Steel 304 | |||||||
C | Horn Antenna Φ76mm / Stainless Steel 304 | |||||||
D | Horn Antenna Φ96mm / Stainless Steel 304 | |||||||
Seal Up / Process Temperature | ||||||||
V | Viton / (-40~150) ℃ | |||||||
K | Kalrez / (-40~250) ℃ | |||||||
Electronic Unit | ||||||||
2 | (4~20) mA / 24V DC / Two wire system | |||||||
3 | (4~20) mA / 24V DC / HART two wire system | |||||||
4 | (4~20) mA / 220V AC / Four wire system | |||||||
5 | RS485 / Modbus | |||||||
Shell / Protection Grade | ||||||||
L | Aluminum / IP67 | |||||||
G | Stainless Steel 304L/ IP67 | |||||||
Cable Line | ||||||||
M | M 20x1.5 | |||||||
N | ½″ NPT | |||||||
Field Display/The Programmer | ||||||||
A | Belt | |||||||
X | Without |